|
| Main Category : TEFLON® Fluoropolymer Coating & Lining |
|
Sub
Category : 1]
TEFLON®/NON-STICK COATING-TEFCOTTM
|
|   |
Visit Homepage for :
 Feedback Form
Trade Enquiry Form
Contact Details
Product Performance Certificates
BLIONTM-A
pinhole free homogenous thick coating of PVDF (KYNAR), FEP, PFA,
ETFE.ECTFE (HALAR). It has the extraordinary chemical resistance
on chemical equipments parts. Any articles of intricacy shape can
be processed. Thickness from 500 to 1000 microns. Any articles of
intricate configurations can be processed.
|
|  
|
Properties:
Temperature ranges
from-100oC to +260oC. Withstands impact force
and elongation up to 30%. Non-stick, Non-toxic, Electrical insulation,
Anti-static and Release-surface. Resistant to almost all chemicals
and solvents.
TOP |
|
Typical Application:
- Vessels
- Agitators
- Stirrers
- Hooppers
- Thermowells
- Spindles
- Dip-Tubes
- Implellers
- Pump Housings
- Manway Covers
|
- Autoclaves
- Sight Glasses
- Heat Exchangers
- Pressure Filters
- Heating Coils
- Steam Ejectors
- Boiler dish
- Nuclear Parts
- Large Parts
- Large diameter pipes
|
- Process Control equipment
- Centrifuge Housings
- Valves
- Bends
- Tees
- Floats
- Flanges
- Springs
- Reducers
- Mushrooms
|
|
TOP
| Metal
Specifiction For-BLION™ Parts
should withstand 450oC without warping or
damage. Parts cannot be painted before coating. All
inside and outside corners to be radioused. All junction
of flanges, nozzles, manway, ID of flange faces to be
ground to a smooth redious. For pipes under 8" minimum
radii of 3/16", to 16" radii of 1/4" and over 16" radii
of 3/8". Nozzles and Manway to be flush with inside
wall of vessel.
All welds on the interior to be ground flush without
splatter, protrusions or pits.
For perforated steel hole diameter to metal thickness
ratio required 1:1 with proper radii. Castings must
be of excellent quality, porosity can cause problems
during process.
Welds must be solid, continous and should contain no
porosity, holes or undercutting. No welding can be done
after coating is applied.
TOP
| PHYSICAL PROPERTIES OF DIFFERENT GRADE OF
BLION™ |
| DESCRIPTION |
UNITS |
BLION™DF |
BLION™TFE |
BLION™FEP |
BLION™PFA |
| Max.temp. |
oC |
-40 to + 150 |
-50 to + 175 |
-80 to + 200 |
-100 to + 260 |
| Tensile Strength |
kg/cm2 |
400-500 |
491 |
180 |
190-200 |
| Izod
Impact Strength |
Kg.cm. |
10
to 12 |
No
Break |
No
Break |
No
Break |
| Elongation |
% |
30 |
40 |
30 |
35 |
| Hardness |
Rockwell/Shore |
R115/D77-82 |
R93/D75 |
R40/D60 |
R45/D65 |
| Abras
Resistant |
Armstong |
0.4 |
0.3 |
0.4 |
0.6 |
| Water
Absorption |
% |
0.04 |
0.01 |
0.01 |
0.01 |
| Dielectric Constant |
103-106HZ |
0.60 |
2.6 |
3.1 |
2.1 |
| Dilectric Strength |
KV
/MM |
14/17 |
21 |
15 |
20-26 |
| Volume Resistivity |
Ohms-Cm |
1.3
x 1012 |
> 1015 |
> 1016 |
> 2.0 x 1015 |
Thermal Conductivity
(ASTM C 177) |
Cal/Sec-1 Cm-1 |
3.10-4 |
4.10-4 |
5.8-4 |
6.10-4 |
| Thermal Expansion |
10-5 oC |
12 |
12-17 |
5-9 |
8-10 |
| Density |
gms
/ c.c |
1.78 |
1.68 |
2.16 |
2.06 |
| Chemical Resistant |
- |
Good |
Very Good |
Excellent |
Excellent |
|
|
|